italoc's Replies | OpenGarage

Forum Replies Created

Viewing 19 posts - 1 through 19 (of 19 total)

Author

Posts
November 1, 2022 at 11:38 am in reply to: Push button every reboot #2510

italoc
Participant

I have bought opengarage from you, and I have 2 device, with same configuration, and only one of this have this problem, but this was not present when I have bought my device, I have noted this after some firmware upgrade

October 24, 2017 at 1:33 am in reply to: Fork with MQTT, Magnetic Sensor support ,Close if left open at night – misc #755

italoc
Participant

The extra pictures require you to manually burn an additional firmware file which can’t be done currently through the GUI – but in your case if you can’t see the vehicle I wouldn’t worry with it.

i have uploaded this file Graphics-placeat00300000.bin more picture are present but not the image of NO VEHICLE

I didn’t understand your response, did you mean No my OG can not see vehicle, if you can’t see the vehicle you can disable detection by setting the vehicle detection threshold to 0 (which I think you probably know as your screenshots appeared to have it off)

My opengarage cant see vehicle, it’s located inside the motor of external gate and use only magnetic sensor for know the position of the gate

October 23, 2017 at 1:28 am in reply to: Fork with MQTT, Magnetic Sensor support ,Close if left open at night – misc #752

italoc
Participant

Also is your OG Unit able to see your vehicle with the distance sensor? I was planning on making it so the firmware had a mode where the built in sensor can be used exclusively for determining if you have a vehicle present and the door sensor used the switch. Let me know if this is of interest (I couldn’t remember if you said you were going to be mounting outside)

no my OG can see vehicle it’s connected to extarnal gate, but i have noticed a little bug in you bin image file, the image of NO VEHICLE is not found…

October 20, 2017 at 5:22 pm in reply to: Fork with MQTT, Magnetic Sensor support ,Close if left open at night – misc #745

italoc
Participant

Hi lawrence_jeff,

Magnetic contact works very well with your firmware, let me know if you need more images

Tomorrow I con mount OpenGarage and magnetic contact on my external gate…

Thanks

Attachments:
You must be logged in to view attached files.

October 20, 2017 at 3:04 am in reply to: Fork with MQTT, Magnetic Sensor support ,Close if left open at night – misc #742

italoc
Participant

@lawrence_jeff

i have received my official opengarage just now, now i update your firmware and during this weekend i mount the magnatic sensor…

October 18, 2017 at 11:50 am in reply to: Fork with MQTT, Magnetic Sensor support ,Close if left open at night – misc #739

italoc
Participant

@lawrence_jeff

my opengarage is still locked in customs

I’m angry with my postal service, they tell me it may take 1 week or 10 days

October 17, 2017 at 12:49 am in reply to: Fork with MQTT, Magnetic Sensor support ,Close if left open at night – misc #737

italoc
Participant

@lawrence_jeff

My package was stopped in customhouse, and postal service say me that can receive it today or tomorrow…

If all is ok i think to test and mount the sensor this evening or tomorrow evening…

I’m waiting…

October 12, 2017 at 1:40 pm in reply to: Fork with MQTT, Magnetic Sensor support ,Close if left open at night – misc #734

italoc
Participant

@lawrence_jeff

Thanks work great…

October 10, 2017 at 9:26 am in reply to: Fork with MQTT, Magnetic Sensor support ,Close if left open at night – misc #721

italoc
Participant

Is there a particular aspect you are interested in – I can get that into the master branch?

Thank you but at the moment it’s not necessary… for me the priority is the magnetic sensor

i think to upload Graphics-placeat00300000.bin on my opengarege because now i can’t see icon, can i use this tool (i use OSX) ?

https://github.com/espressif/esptool

after flashing i lost all setting?

thanks

October 10, 2017 at 2:24 am in reply to: Fork with MQTT, Magnetic Sensor support ,Close if left open at night – misc #719

italoc
Participant

Hi lawrence_jeff,

during this week-end i think to receive a new official opengarage and i try to mount the sensor, and of course i send you some picture.

the GPIO4 and GND contact are located on the LEFT-TOP of the device.

i have installed your firmware on my actual opengarage and seems to work very well and much better than original firmware, but the interface have some difference with your screenshot, for example i cant see VEHICLE TRESHOLD field, it’s normal?

October 9, 2017 at 12:06 pm in reply to: Fork with MQTT, Magnetic Sensor support ,Close if left open at night – misc #714
italoc
Participant
Yes, I just have one official OpenGarage device that I use for my internal garage door, I’M waiting the second for the external gate
- This reply was modified 7 years, 3 months ago by italoc.
Attachments:
You must be logged in to view attached files.
October 9, 2017 at 10:11 am in reply to: Fork with MQTT, Magnetic Sensor support ,Close if left open at night – misc #712

italoc
Participant

Hi lawrence_jeff,

during this week i receive all material for test your firmware, can you explain me how to connect a magnetic sensor to an official opengarage device?

I suppose to connect to GPIO4 and GPIO5, but it’s only my personal opinion….

thanks

September 30, 2017 at 10:13 am in reply to: Fork with MQTT, Magnetic Sensor support ,Close if left open at night – misc #702

italoc
Participant

I would expect that switch to work fine. Just to be clear though you don’t really need this with an official opengarage device unless for some reason the built in ultrasonic sensor won’t work for some reason.

in this case i don’t need ultrasonic sensor but only a magnetic sensor… can you say mw how connect the sensor to official opengarage?

thanks

September 28, 2017 at 3:15 pm in reply to: Fork with MQTT, Magnetic Sensor support ,Close if left open at night – misc #699

italoc
Participant

thank you Lawrence

I think to use this sensor

https://www.amazon.it/dp/B00901DDYU/ref=wl_it_dp_o_pC_S_ttl?_encoding=UTF8&colid=WKAFHZHA7NIZ&coliid=I2DJ6UQLXIA59N

I’m waiting your info

September 28, 2017 at 4:53 am in reply to: Fork with MQTT, Magnetic Sensor support ,Close if left open at night – misc #695

italoc
Participant

let me know, i’m very intrested

September 28, 2017 at 1:41 am in reply to: Fork with MQTT, Magnetic Sensor support ,Close if left open at night – misc #693

italoc
Participant

you can’t find any option in options page?

in github readme i see this:

“Option page changes

Support for added functions – like magnetic switch sensor type and close at certain time”

let me know

September 25, 2017 at 7:15 am in reply to: Fork with MQTT, Magnetic Sensor support ,Close if left open at night – misc #691

italoc
Participant

I like your fork and i think to try your firmware with a magnetic conact, but i have a question:

mangetic contact need to be connected to GPIO4 and GPIO5 correct?

a magnetic contact like this is ok ?
https://www.amazon.it/dp/B00901DDYU/ref=wl_it_dp_o_pC_S_ttl?_encoding=UTF8&colid=WKAFHZHA7NIZ&coliid=I2DJ6UQLXIA59N

thanks

September 23, 2017 at 5:34 am in reply to: Box ip68 trasparent #689

italoc
Participant

Can I use one of this magnetic sensor?
http://salestores.com/secolarmsm4601.html#.WcY31XrOPmo

And connect this one to GPIO 4 and 5?

Thanks

September 23, 2017 at 2:15 am in reply to: Box ip68 trasparent #688

italoc
Participant

your solution is very intresting… how it’s work your solution? which is the range of magnetic sensor?

my idea is to use opengarage on my external GATE anche put opengarege inside/near the motor and use it for know the status (open/closed) of my GATE

Can you help me?

thanks
Author

Posts

Viewing 19 posts - 1 through 19 (of 19 total)

Forum Replies Created

Attachments:

Attachments: